A filter bed is a leaching bed where effluent is spread over at least 750 mm of specified sand, and that sand treats it before anything reaches your native soil. Because the sand is a known material, the Ontario Building Code sizes the bed by how many litres per square metre it can take each day, not by how slowly your soil drains. That is why a filter bed can take up far less surface area than a trench bed for the same house.
It is still a Class 4 system: a septic tank (or a treatment unit) followed by a leaching bed. Only the bed changes. If the basic parts are new to you, start with our guide to what a drain field is and how it works. This post covers one bed design that turns up on a lot of Kawartha Lakes site plans, usually without much explanation.
The rules below come from Subsection 8.7.5 of the 2024 Ontario Building Code (O. Reg. 163/24, in force since 1 January 2025). The province publishes the official text through its Building Code page; we read the filter bed articles on codeindex.ca and link them where they apply.
Filter Bed vs Leaching Bed: One Is a Kind of the Other
In Ontario, “leaching bed” is the umbrella term for the part of a Class 4 system that gets effluent into the ground. A filter bed is one type of leaching bed. The comparison people usually mean is a filter bed against a conventional absorption trench bed: long runs of perforated pipe in stone, buried in native soil.
| Conventional trench bed | Filter bed | |
|---|---|---|
| What treats the effluent | The native soil around the trenches | Imported filter sand first, then the soil beneath it |
| What sets the size | Pipe length, from daily flow and the soil’s percolation time (T) | Sand surface area, from a fixed loading rate |
| Surface area of the distribution bed | Grows as T gets slower | 10 to 50 m² per bed |
| Below the stone | Native soil | At least 750 mm of filter sand, unsaturated for its full depth |
| What gets trucked in | Mostly stone and pipe | Stone, pipe and a lot of sand |
Our post on leaching bed size and depth in Ontario works through the trench math, where every extra minute of percolation time adds pipe. A filter bed breaks that link for the top of the bed. Native soil still matters, but only for the footprint underneath.
Two things are easy to confuse with it. A shallow buried trench is a separate Part 8 design, and a packaged sand or media filter is a treatment unit that sits ahead of a bed, not the bed itself.
How the Building Code Sizes a Filter Bed
The sand surface: a loading rate, not a perc test
Article 8.7.5.2 sets the loading requirements for filter beds:
| Situation | Maximum loading on the sand surface |
|---|---|
| Daily design flow up to 3,000 L, septic tank ahead | 75 L/m² per day |
| Daily design flow over 3,000 L, septic tank ahead | 50 L/m² per day, split across more than one filter bed of similar size, side by side |
| Level II, III or IV treatment unit ahead | 100 L/m² per day |
Each filter bed must have an effective sand area of at least 10 m² and no more than 50 m². Article 8.7.5.1 caps the whole system at 5,000 L a day behind a septic tank, or 10,000 L a day behind a Level II, III or IV unit. Where there are several filter beds, their distribution pipes must be at least 5 m apart.
Say you have a three-bedroom house. Its Code daily design flow is 1,600 L, before any adders for floor area or fixture count. Divide by 75 and the sand surface has to be at least about 21.3 m², one bed. Put a Level IV treatment unit in front of the same house and the floor drops to 16 m². The designer’s figure will often be a little higher, because the pipes must be evenly spaced with the outermost line no more than 600 mm from the edge of the sand.
Underneath: the contact area
Article 8.7.5.3 requires the base of the filter medium to spread at least 250 mm thick over a contact area with the native soil, calculated as A = Q × T ÷ 850. Q is the daily design flow in litres and T is the percolation time of the soil underneath, capped at 50 for this formula. Designers often call this spread the mantle.
For the same three-bedroom house at 1,600 L:
| Soil under the bed | Contact area needed |
|---|---|
| T = 20 | about 37.6 m² |
| T = 40 | about 75.3 m² |
| T = 50 or slower (formula caps at 50) | about 94.1 m² |
So a filter bed on slow soil still needs ground, just in a different shape. The pipes stay packed into a small sand surface, and the sand base fans out underneath to hand effluent to the native soil over a wider area.
Depth rules that decide whether it gets raised
Three more lines in 8.7.5.3 shape what you see in the yard:
- The filter sand must be at least 750 mm deep below the stone layer (or the bottom of leaching chambers), and it must be clean sand inside a specified grain-size band. Ordinary pit fill does not qualify.
- The sand must stay unsaturated for its entire depth.
- The stone layer must sit at least 900 mm above the high groundwater table, rock, or soil with a percolation time over 50 minutes.
That 900 mm rule is what pushes filter beds up out of the ground on waterfront and shallow-rock lots. If the water table or bedrock is close to the surface, the only way to get the separation is to build upward.
When a Designer Chooses a Filter Bed
The bed type is decided by a licensed sewage system designer after a site evaluation: usually a perc test at $500 to $1,500, and often a soil profile or deep test pit at $500 to $1,000. A filter bed tends to come up in four situations.
The lot is short on usable area. Setbacks from a well, the lake and the lot lines can leave a small envelope, and a trench bed on slower soil sprawls past it. A compact sand surface is one way to fit a compliant bed into what’s left. Our post on septic systems for small lots in Ontario covers the other options.
The native soil is poor at treating effluent. Very slow soil backs effluent up. Very fast soil, like coarse sand and gravel, moves it along before much treatment happens. A known depth of specified sand in the path gives the designer a treatment layer they can count on.
Groundwater or rock is close to the surface. The 900 mm separation often means a partly or fully raised filter bed, and then the Code’s raised-bed construction rules apply too: fill compacted in layers so the pipes do not settle unevenly, side slopes no steeper than 1 in 4 (1 in 3 with erosion control), and the pipe clearances in Table 8.2.1.6.B increased by twice the height the bed is raised above original grade. Those clearances start at 15 m from a drilled well with a watertight casing at least 6 m deep and 30 m from a dug well, so a bed raised 1 m needs 17 m and 32 m. Municipalities and conservation authorities can require more.
There is a treatment unit in the design. Behind a Level II, III or IV unit, the sand can take 100 L/m² a day instead of 75, which shrinks the bed again.
A filter bed is not a Type A dispersal bed or a fully raised sand mound, though all three use imported sand. See our posts on Type A dispersal beds and raised sand beds and on raised bed and mound systems.
What a Filter Bed Costs in Kawartha Lakes
We do not publish a separate filter bed price, because the number depends on how much sand has to be trucked in and whether the bed sits in the ground or on top of it. These are the published figures that frame it:
| System | Typical installed cost (Ontario) |
|---|---|
| Conventional full system (tank and tile bed), good soil | $15,000 to $22,000 |
| Raised mound system | $25,000 to $45,000 |
| Tertiary / Level IV treatment system, installed | $28,000 to $45,000 |
| Leaching bed replacement only, tank stays | $10,000 to $25,000 |
An in-ground filter bed on a lot with room to work behaves more like the first row. A filter bed raised well above grade on a wet or rocky waterfront lot carries the fill, compaction and slope work that drive the mound price.
Permitting and design run $3,000 to $7,000 for a standard Class 4 residential system before any digging. In the City of Kawartha Lakes the Class 4 permit is $975 for a new system up to 4,500 L a day and $461 for tank replacement or bed repair; ask the City’s Building and Septic Division (705-324-9411) which applies to your job. A replacement usually takes 4 to 8 weeks from first call to finished system, with 2 to 5 days of excavation on site.
The design is stamped by a licensed sewage system designer. We handle the excavation, the installation and booking the inspections, and every job starts with a site visit and ends with a written, itemized quote. Our installation and replacement page explains how that runs, and the replacement cost estimator gives a first number.
Living With a Filter Bed: What Not to Do on Top
The general rules are in our post on what can go over a leaching bed: grass yes, driveways, sheds, pools and trees no. A filter bed adds a few of its own, each traceable to how the Code builds it.
Keep extra water off it. The sand has to stay unsaturated for its full depth. Downspouts, a sump discharge, driveway runoff or a sprinkler zone aimed at the bed all work against that, and sand that stays wet stops treating.
Keep weight off it. The fill under a raised filter bed is compacted in layers so the pipes stay level. A parked truck, a hot tub or a skid steer crossing it for a landscaping job can undo that.
Leave the slopes and the edges alone. On a raised bed the side slopes are part of the design and stay stabilized under grass, and the sand base spreads beyond the pipes. Cutting into the toe of the slope for a patio or retaining wall can open the side of the bed or cut off part of the contact area.
Do not add soil or build garden beds on it. Extra fill changes the cover the design assumed, and gardens mean digging and watering.
Keep solids in the tank. The sand surface is what clogs when sludge and scum carry over. Pump every 3 to 5 years for most households (our pumping frequency guide breaks it down by household size), and keep the effluent filter clean if your tank has one. A replacement filter runs $50 to $150.
On a raised bed, trouble often shows first at the edges: soggy ground or odour at the toe of the slope, or a strip of unusually green grass downhill. A struggling bed is not automatically a replacement. We diagnose before we replace, and our drain field repair page explains rehabilitation against replacement.
Frequently Asked Questions
Is a filter bed the same as a raised bed?
No. A filter bed is defined by its layer of specified filter sand, at least 750 mm deep, and it can be built in the ground, partly raised or fully raised. It gets raised when the water table, rock or very tight soil is too close to the surface to leave 900 mm below the stone layer.
How big is a filter bed for a three-bedroom house?
Behind a septic tank, the Ontario Building Code limits loading on the sand surface to 75 L per square metre a day for flows up to 3,000 L. A three-bedroom house has a daily design flow of 1,600 L, so the sand surface needs at least about 21.3 m². The sand base spreads wider underneath, over a contact area that depends on how slowly the native soil drains.
Is a filter bed cheaper than a conventional leaching bed?
Usually not on a lot where a conventional trench bed fits, because the filter sand has to be bought and trucked in. A conventional full system on good soil runs $15,000 to $22,000 in Ontario. The filter bed earns its cost on lots where a trench bed will not fit or will not pass, and the other choice is a raised mound at $25,000 to $45,000 or a tertiary system.
Can you put a filter bed on clay soil?
Sometimes, but the clay still counts. The Code sizes the contact area under the sand using the soil’s percolation time, capped at 50 minutes, and requires the stone layer to sit at least 900 mm above any soil slower than 50 minutes. On heavy clay that usually means a raised filter bed with a large sand footprint, and whether it works is the designer’s call after a perc test.
Have a Filter Bed on Your Drawing?
If a designer has specified a filter bed and you want to know what it means for the price and the dig, call (705) 702-5526 or book a site visit. We’ll walk the lot, go through the design with you and leave a written, itemized quote. Callbacks go out within 24 hours in business hours.
There is no travel surcharge anywhere in the City of Kawartha Lakes. For Peterborough County, Durham Region, Belleville and Hastings, and Haliburton, the price is quoted up front before any work is booked.