Kawartha Septic truck on a rural Ontario property
Septic Guide

Sand Filter Septic Systems in Ontario: How They Work and When They're Used

A sand filter septic system is a septic tank followed by a contained bed of specified sand. The tank's effluent is pumped onto the sand in small doses, bacteria on the grains clean it further, and onl

By the Kawartha Septic service team · Published

A sand filter septic system is a septic tank followed by a contained bed of specified sand. The tank’s effluent is pumped onto the sand in small doses, bacteria on the grains clean it further, and only then does it go to the leaching bed. The filter treats. The leaching bed after it is still where the water leaves the system.

That matters because “sand” turns up all over Ontario septic designs. Raised beds are built on imported sand. So are filter beds. A sand filter is a different thing: a box of engineered media that cleans effluent before it is dispersed at all.

Most people meet the term on a designer’s drawing, after a perc test and soil profile have shown the lot cannot take a conventional bed on its own.

What a Sand Filter Does Between the Tank and the Bed

A conventional Class 4 system has two working parts: the tank separates solids, and the soil under the leaching bed finishes the treatment. Ontario’s septic classes explained covers that baseline. A sand filter adds a stage in the middle:

  1. Septic tank. Solids settle, scum floats, clarified liquid leaves through the outlet.
  2. Dosing chamber. The liquid collects, and a pump sends it to the filter in timed or float-triggered doses.
  3. Sand filter. Small pressurized pipes spread each dose over the sand. It trickles down through unsaturated sand, where the biology happens, and an underdrain collects it at the bottom.
  4. Dispersal. The cleaner effluent goes to a leaching bed, often smaller or shallower than the lot would otherwise need.

Dosing is the trick. Sand that stays flooded goes anaerobic and clogs. Sand that gets a small dose, drains and gets air between doses stays aerobic, and aerobic bacteria clean effluent far more thoroughly than the anaerobic ones in the tank.

Single-Pass and Recirculating Sand Filters

Your quote will name one of two designs.

A single-pass (intermittent) filter sends each dose through the sand once, then on to the bed. Simple, but the sand gets one chance at the water, so the filter needs more area.

A recirculating filter drains into a recirculation tank, where the filtered water mixes with fresh tank effluent and most of it goes back over the sand. Only a portion moves on to the bed each cycle. The US EPA’s fact sheet on recirculating sand filters describes it as a modified version of the old single-pass open filter, developed partly to deal with odour.

Single-passRecirculating
Passes through the sandOnceSeveral; EPA lists 3:1 to 5:1 recirculation as typical
Extra tankDosing chamberRecirculation tank, at least one day’s raw flow per EPA
Filter footprintLargerAbout one-fifth the area of a single-pass filter, per EPA
ControlsPump and float or timerPump, timer and a valve that splits the flow
Sand depthSet by the designEPA’s typical figure is 24 inches (about 600 mm) over graded gravel

EPA reports roughly 85 to 95 percent removal of BOD and suspended solids from recirculating filters, with almost complete nitrification. Those are figures from American installations, not a promise about a unit sold here. For your permit, what counts is the treatment level the unit is rated to.

How Ontario’s Building Code Treats a Sand Filter

The current Code is the 2024 Ontario Building Code, O. Reg. 163/24, in force since 1 January 2025; the province’s Building Code page is the official starting point.

A sand filter used as a separate treatment stage is, in Code terms, a treatment unit other than a septic tank. Article 8.6.2.2 requires its effluent to stay under maximum concentrations, averaged over 30 days, for its treatment level:

Treatment levelSuspended solidsCBOD5
Level II30 mg/L25 mg/L
Level III15 mg/L15 mg/L
Level IV10 mg/L10 mg/L

The article accepts certification to CAN/BNQ 3680-600, the national standard for onsite residential treatment technologies, as proof a unit meets its level. If someone proposes a site-built sand filter with no rating behind it, ask the designer how it will be approved, and check with the City before anything is dug.

The same article says a treatment unit feeding a shallow buried trench, a Type A dispersal bed or a Type B dispersal bed must meet Level IV. The dispersal method and the treatment unit are chosen together; our post on Type A dispersal beds and raised sand beds covers the bed side.

Owning a treatment unit also brings obligations. A mechanical unit needs an audible and visual alarm and a way to sample the effluent, and the owner has to hold the manufacturer’s operating and maintenance literature. Under Article 8.9.2.3, nobody may operate a treatment unit other than a septic tank without an agreement for servicing by someone the manufacturer authorizes to service that type of unit. The Code also sets effluent sampling duties, with results reported to the chief building official. How those apply to your design is a question for the designer and the City’s Building and Septic Division, 705-324-9411.

Sand Filter or Filter Bed: Two Different Things

This is the mix-up we hear most. A filter bed is a type of leaching bed under Code Section 8.7.5, so it is a dispersal method. Effluent goes into stone and pipe laid over imported filter sand, which the Code sets at a minimum of 750 mm below the stone and requires to stay unsaturated for its full depth. The water soaks through the sand into the ground. Nothing is collected at the bottom.

A sand filter collects the water in an underdrain and sends it on, usually to a leaching bed.

The two can work together. Article 8.7.5.1 caps a filter bed at 5,000 L of total daily design flow when the treatment unit is a septic tank, and 10,000 L when it is a Level II, III or IV treatment unit. Better treatment upstream lets the bed carry more.

Where a Designer Chooses One

The EPA’s list of sites suited to sand filters could describe cottage country: shallow soil, poor permeability, high groundwater, limited land area. Around the City of Kawartha Lakes that means thin soil over limestone, Shield rock near the surface up north, clay around Lindsay, and small shoreline lots where setbacks leave little room.

A common pattern is a lot that fails on two counts. Say the soil is shallow to rock and the lot is too tight for a full raised bed or mound. Treating the effluent first can allow a smaller dispersal area, and that is what makes the design fit.

Sand filters belong to the same family as the peat, foam and aerobic units in our guide to advanced treatment units. Between them, the designer weighs each unit’s rating, footprint and power draw, and who locally is authorized to service it. The lot decides whether you need extra treatment. The design decides which kind.

What a Sand Filter Costs

We do not publish a sand-filter price, because we do not have one we can stand behind. It depends on the unit, whether it recirculates, the bed it feeds and the site, and it is quoted after a site visit from the designer’s specification. Here is where it sits against the system types we do price:

System typeTypical installed range in Ontario
Conventional full system (tank and tile bed), good soil$15,000 to $22,000
Raised mound system$25,000 to $45,000
Tertiary / Level IV treatment system$28,000 to $45,000

A sand filter adds a treatment stage, a pump, controls and often a second tank to a conventional layout, so expect it above the conventional row. Where the filter is the Level IV unit feeding a Type A bed, the tertiary row is the closer comparison. Soil testing, design and the permit add $3,000 to $7,000 for a standard Class 4 residential system, and the City of Kawartha Lakes permit for a standard Class 4 is $975.

Our septic system replacement cost guide breaks down each line item behind the overall range of $15,000 to $35,000 in Ontario, with most jobs landing between $15,000 and $30,000.

Looking After One

A sand filter adds to the maintenance list. It does not replace anything on it.

The tank still gets pumped, and the interval matters more, because the tank is what keeps solids off the sand. Every 3 to 5 years suits most households, adjusted for how many people live there, and a routine pump-out on a 1,000 to 1,500 gallon tank runs $300 to $600. The outlet filter still gets cleaned too, since anything that escapes the tank ends up on the sand. Effluent filter cleaning covers that job; a replacement filter is $50 to $150.

EPA’s recommended routine checks the pumps, controls and timer every three months and flushes the distribution pipes once a year. Your service agreement sets the actual schedule for your unit. An effluent pump typically lasts 7 to 10 years, and replacing one runs $600 to $1,500.

The sand has no fixed replacement date. EPA notes that if a filter is overloaded, with too much water or too much organic load, the top of the media can clog and may need replacing if the cause is not fixed in time. Water use, what goes down the drain and pumping on schedule are what keep it from getting there.

Winter and power

The filter runs on a pump, so it stops treating in a power cut. The tanks hold some flow, not an unlimited amount; septic systems in a power outage covers how to ration water until the power is back. Cold is the other design issue. EPA says very cold climates need designs that stop standing water freezing, with distribution lines that drain between doses and an insulated filter. If the alarm sounds in January, call for service rather than waiting for spring.

Frequently Asked Questions

Is a sand filter the same as a filter bed?

No. A sand filter is a treatment unit that cleans septic tank effluent and collects it at the bottom to send on to a leaching bed. A filter bed is itself a leaching bed, built over a layer of imported filter sand, and the effluent soaks through it into the ground. The Ontario Building Code deals with them in different sections, and one system can include both.

How much does a sand filter septic system cost in Ontario?

There is no single figure, because the price depends on the unit, whether it recirculates, the bed it feeds and the site. For comparison, a conventional system on good soil runs $15,000 to $22,000 and a tertiary or Level IV treatment system runs $28,000 to $45,000 installed. A sand filter adds a treatment stage to a conventional layout, so expect it above the conventional range and get it quoted from the designer’s specification after a site visit.

Does a sand filter septic system need electricity?

Almost always. The effluent is pumped onto the sand in small doses, and a recirculating filter also pumps filtered water back over the sand several times. When the power is out the filter stops treating, so keep water use low until it is restored.

Do I still need to pump the septic tank if I have a sand filter?

Yes. The tank keeps solids away from the sand, and solids carried onto the filter are one of the main ways it clogs. Most households pump every 3 to 5 years, adjusted for how many people live in the house, and the effluent filter should be cleaned at each visit.

Who is allowed to service a sand filter in Ontario?

The Ontario Building Code says a treatment unit other than a septic tank may only be operated under an agreement for servicing by a person the manufacturer authorizes to service that type of unit. Your designer or installer should tell you who that is before the system goes into use. Keep the agreement and the manufacturer’s literature with your permit papers, because a buyer will want to see them.

Pumping and Installs Around a Sand Filter

If your designer has specified a sand filter, we can talk through the installation. The design is stamped by a licensed sewage system designer; we handle the excavation, installation and inspections booking. Septic system installation explains how that works.

If you already own one, the tank upstream still needs pumping on schedule. Call (705) 702-5526 or book a pump-out. Most routine pump-outs are scheduled within 48 hours, with no travel surcharge anywhere in the City of Kawartha Lakes. For Peterborough County, Durham, Belleville and Haliburton, the price is quoted up front before the truck is booked.

Still not sure what your system needs?

Leave a number and where the property is. We will call you back with a straight answer and a real price — not a form letter.

Or call (705) 702-5526 — 24-hour emergency line.

Continue Reading